Skateboards aren’t just for cruising sidewalks or pulling off tricks at the skatepark, they’re built tough, layered with character and often carry years of stories in their scrapes and stickers.
So when one finally gets retired, it feels like a waste to just toss it. That’s where creativity comes in. Whether you’ve got broken decks gathering dust or just love the idea of turning something rugged into something beautiful, recycled skateboard projects can bring bold color and personal flair into your home.
From shelves and stools to jewelry and wall art, we’ve rounded up 25 brilliant ways to give those boards a second life and trust me, you’ll want to try them all.
There’s something wonderfully nostalgic about a tree swing, and this upcycled skateboard version amps it up with a splash of adventurous spirit.
Moreover, hanging from a sturdy branch deep in the woods, it invites wild rides, belly laughs, and that freeing whoosh of air as you sail above the forest floor.
Step 1: Remove any hardware from the skateboard and sand the deck to smooth out rough edges or chipped paint.
Step 2: Drill two holes near each end of the board, about 2 inches in from each side.
Step 3: Thread the ropes through the holes, knotting underneath securely. For added grip, you can double-knot and test for slippage before use.
Step 4: Throw the rope ends over your chosen tree branch and tie them tightly using a bowline or figure-eight knot.
This DIY shoe rack made from stacked skateboard decks is the kind of project that speaks to both your skater soul and your need for functional space.
Perfect for a dorm, studio, or your old room back at your folks’ place, this rack helps your home organize, and of course you'll not be mad anymore.
Step 1: Mark and drill holes in each skateboard deck to align with your chosen side panels. You can use a spade bit to drill clean, wide holes for the bolts.
Step 2: Position the decks evenly between the two side panels and bolt them in place, tight enough to be sturdy, but not so tight that it warps the wood.
Step 3: If desired, decorate the side panels with spray paint, stickers, or a personal stencil design for a custom finish.
Step 4: Finally, fill your new rack with shoes, skate gear, or collectibles.
This wall-mounted setup takes old skateboard decks and transforms them into a gritty, functional statement piece. Thanks to this project, each deck is now living on as hat racks, coat hangers, and shelves for shoes or gear.
Additionally, the decks are mounted flat as shoe racks near the floor, while the upper zone uses trucks and hangers to support hats, jackets, and even a backpack.
Step 1: Clean each skateboard deck thoroughly but leave the scratches and stickers as it’s part of the charm.
Step 2: Decide on your layout. Start from the bottom with the shoe racks, spacing them just enough for your tallest pair.
Step 3: Attach L-brackets to each end of the deck, then drill them into the wall using anchors for extra support.
Step 4: Use old trucks or wall hooks to hang hats, coats, and backpacks on the upper section. You can even screw the trucks directly into the wall studs for maximum hold.
Instead of retiring the board, it’s been given a second life as a floating plant perch, adding a bit of gritty charm above a mirror while giving those houseplants a spotlight.
What stands out most is the balance, you can see the tough, graffitied aesthetic of the board contrasted with the lush, green softness of the plants.
Step 1: Clean the skateboard deck, leaving any stickers or scuffs that tell its story. You can also add a light coat of clear sealant.
Step 2: Mark the placement of your shelf brackets on the wall. Make sure they're level and spaced to fit just inside the trucks area.
Step 3: Secure the brackets to the wall using heavy-duty anchors, especially if you plan to place plants or other weighty items on the shelf.
Step 4: Rest the skateboard deck on top and screw it into the brackets through the underside or use rubber stoppers to hold it snugly.
Wow, this upcycled table is a raw, rebellious centerpiece that breathes attitude into any room. Whether in your entryway, workshop, or studio corner, it’s bound to spark a conversation.
Step 1: Select your most weathered yet colorful decks for the tabletop. Then sand them gently to smooth out rough areas without erasing the character.
Step 2: Arrange and glue the decks together side by side, trimming edges if needed to make a flat surface.
Step 3: Cut your support legs from hardwood, angling the bottoms slightly outward for stability. Next, attach them underneath the bench using screws and glue.
Step 4: Finish with a protective clear coat or leave it raw for an authentic streetwear look.
This one-of-a-kind coffee table transforms worn-out skateboard decks into a layered, industrial-style centerpiece.
I believe no matter you're furnishing a dorm room or adding flair to a man cave, this project brings in personality, color, and skate culture. Specially, the rolling wheels even give it the option to glide around your space with ease.
Step 1: Clean all skateboard decks thoroughly and sand down any sharp edges or peeling paint.
Step 2: Mark and drill four holes on each of the two lower decks where the rods will connect.
Step 3: Attach the metal rods vertically using flange plates, washers, and nuts. You should make sure everything is tightened firmly with your wrench.
Step 4: Stack the decks as desired, securing each one with its rod set. You can adjust the spacing based on how tall you want the table and how much storage you’d like in between layers.
This tiny picnic table, made from old skateboard decks, invites just that. With a bit of street-style flair, kids and even adults will love this project.
Moreover, when summer comes, this project is for finger painting, chalk doodles, or snack time under the sun.
Step 1: Cut and assemble your wooden base into a classic picnic table frame.
Step 2: Secure the skateboard decks horizontally as seating on either side using strong screws through pre-drilled holes.
Step 3: For the tabletop, split a skateboard lengthwise, leaving a gap in the center if desired for style or function. You want to secure both halves to the top crossbeams.
Step 4: Seal the wood and sand any rough edges on the decks to avoid splinters. Paint the tabletop in chalkboard black if you want a creative twist.
These eye-catching upcycled chairs use old snowboard decks as both the seat and the high, dramatic backrest forming the perfect blend of slope style and sleek outdoor design.
Perfect for patios, cabins, or even man caves with winter-sports vibes, these chairs are as much art as they are furniture.
Step 1: Clean and sand down the snowboard deck. If graphics are peeling, consider resealing it with clear polyurethane.
Step 2: Cut the board if necessary to size the backrest and seat separately or you can use one continuous deck as shown for a sleeker style.
Step 3: Drill holes into the deck and metal frame for secure bolting. Then, use washers to prevent damage to the board.
Step 4: Assemble the frame and attach the snowboard deck using bolts and locking nuts.
Instead of letting skateboards clutter the floor, why not show them off? This vertical wall-mounted setup turns your stairway into a sleek gallery of longboards and cruisers, each resting snugly on sturdy hooks.
Bonus, the graphics, grip tape, even wheel color choices reflect personality, and hanging them like this makes the most of tight hallway space without sacrificing vibe or accessibility.
Step 1: Choose a visible wall with enough vertical space for your collection. A stairway like this works great to follow the incline and create a dynamic line.
Step 2: Measure and mark where each pair of hooks will go, leaving enough space for the width and height of your boards.
Step 3: Drill in the wall anchors first if you're not hitting studs. Then install the brackets securely.
Step 4: Hang each board horizontally with the wheels facing out.
Turning broken decks into vertical plant holders is a beautiful contradiction. You take something rough and worn, and let it cradle something alive.
In addition, these skateboard wall planters bring energy, motion, and color into any room.
Step 1: Clean the decks and remove the wheels and trucks if still attached.
Step 2: Hold each skateboard vertically against the wall, mark the top and bottom screw holes, and drill into anchors.
Step 3: Secure the boards with screws so they hang solidly and don’t tilt.
Step 4: Loop or tie plant hangers through the truck holes or around the board body, and nestle your potted plants in.
This half-deck key holder brings together grit, charm, and just enough attitude to make a plain wall pop.
Whether you’re tossing in your keys after a ride or scribbling quick notes with chalk, this piece proves that even broken boards can come home in style.
Step 1: Start with a clean, sanded board piece. If needed, cut your old skateboard into a clean half shape.
Step 2: Paint the top portion with chalkboard paint. Let it dry, then apply a second coat for durability.
Step 3: Write your favorite phrase using chalk, something fun or personal like “Home SKATE Home.”
Step 4: Attach screw hooks evenly spaced along the bottom edge to hang keys. Now you can mount to a wall using screws.
Who says a wine rack can’t ride the edge of rebellion? This upcycled skateboard-turned-wine holder is a bold blend of street style and refined taste.
Furthermore, the board’s bold, abstract graphics make the whole setup pop like a label from a limited-edition vintage.
Step 1: Clean the board and remove the trucks. Sand lightly if needed.
Step 2: Position and mark where the metal holders will go to cradle the bottle horizontally, one near the top, one at the base of the bottle.
Step 3: Screw the holders into the deck. Make sure they’re snug and well-aligned to support the weight.
Step 4: Finally, mount the deck vertically on the wall with screws or hooks.
This one’s got nostalgia and style written all over it. Instead of tucking away old photos in dusty albums, why not turn a retired skateboard into a heartfelt tribute to your best memories?
Whether it’s a gift for a friend, a DIY dorm room accent, or a personal keepsake, this project brings personality and warmth to any wall.
Step 1: Start by cleaning and lightly sanding the deck to remove any dirt or rough patches.
Step 2: Arrange your frames on the board to plan spacing. You can alternate between vertical and horizontal placement or keep it symmetrical.
Step 3: Once satisfied with the layout, use wood glue or a heavy-duty adhesive to secure each frame onto the deck. Then, press down firmly and allow to dry per the glue’s instructions.
Step 4: Add your printed photos inside each frame. Now, you can attach hanging hardware to the back of the deck for wall mounting.
With this boldly painted skateboard clock, you get a pop of color and a conversation starter. This deck has been given new life with chunky brush strokes in vibrant, contrasting block and at the center, a simple clock mechanism ticks away.
Step 1: Sand the surface of the skateboard to remove any residue or old graphics.
Step 2: Block out your color zones with light pencil marks or painter’s tape. Then, fill in each section with your chosen paints.
Step 3: Drill a hole in the center of where you want the clock hands to be. This should be around the upper third of the board for a balanced look.
Step 4: Insert the clock movement from the back, attach the hands, and secure the mechanism per the kit’s instructions. Now, add batteries and set the time.
Step 5: Mount on the wall using hooks or anchors, and enjoy your upgraded timepiece!
When your board's got too many scrapes to ride, why not let it light up your world instead? This rad wall lamp transforms an old, battle-scarred deck into a glowing piece of wall art.
With exposed bulbs and pipe fittings, it brings gritty, industrial charm, ideal for a creative workspace, studio, or teen bedroom.
Step 1: Clean the skateboard surface, but don’t erase the scuffs, then drill holes for the wiring and mounting hardware.
Step 2: Mount the pipe fittings securely onto the deck using screws. You want to attach the light sockets at each end of the pipes.
Step 3: Wire the sockets to your plug-in cord or wall wiring, depending on your setup.
These shelves are bold, personal, and undeniably cool. Each board carries scuffs and scrapes like badges of honor, now reborn to hold houseplants, pottery, or quirky keepsakes.
Step 1: Clean each skateboard deck and decide the placement order based on their art, wear, or color.
Step 2: Hold each board against the wall and mark where your brackets will go, you should use a level to ensure they’re straight.
Step 3: Drill holes into the wall for each bracket, insert anchors, and screw in the brackets tightly.
Step 4: Place each skateboard deck over the brackets, centered, and screw the deck onto the brackets through the underside.
Step 1: Cut the skateboard decks to preserve the curved tail section. Each piece should be around 10-12 inches long.
Step 2: Lightly sand all the edges to remove splinters, but don’t overdo it, you want to keep the worn-in look.
Step 3: Attach the support blocks behind each board piece to serve as mounting bases and stability anchors for the hooks.
Step 4: Drill holes through the board and into the wall, using anchors if needed. Secure tightly, and you’ve got two seriously cool hooks for coats, bags, or gear.
This eye-catching bookshelf made from colorful skateboard decks isn't just storage, it’s a creative punch to any dull corner of your room.
Specially, five repurposed boards, each a different hue, bring playful energy while stacking books, magazines, or collectibles in a vertical layout that’s both functional and full of personality.
Step 1: Drill four evenly spaced holes near the corners of each skateboard deck to fit the rods.
Step 2: Slide a washer and nut onto each rod. You should place the bottom deck over the rods and tighten to hold it in place.
Step 3: Add another washer and nut set at the height you want the next shelf to sit.
Step 4: Finally, secure the top deck with final nuts and washers.
You know that board you’ve worn down to splinters and stories? Don’t toss it, transform it. These upcycled slingshots carve new life into broken decks, turning battle-scarred maple into hand-crafted fun.
Step 1: Sketch and cut out your slingshot shape from a smooth section of the deck using a jigsaw or bandsaw.
Step 2: Sand down the entire piece, especially the edges, until it’s safe and comfortable to hold.
Step 3: Drill two holes at the top arms to thread the rubber bands through securely.
Step 4: Cut a small leather square and punch two tiny holes on each side. Then, thread and knot your rubber bands or tubing onto the leather to form the sling.
Step 5: Attach each end of the band to the slingshot arms, double-knotting them to hold firm.
This sleek, minimalist phone stand brings old-school charm to your desk or kitchen counter. Made from a trimmed skateboard deck, it tilts just right for scrolling, watching videos, or reading recipes while you cook.
Step 1: Cut the tail end of an old skateboard to a manageable phone-stand height (around 10-12").
Step 2: Cut two base pieces to support the upright back including one for the angle brace, one for the phone rest.
Step 3: Glue or screw the base pieces into place. You should ensure the angle is comfortable for viewing and stable.
Step 4: Optionally stain or seal the wood for a polished look, or leave it raw for rustic appeal.
Who says your bathroom can’t have personality? This quirky toilet paper holder turns a plain skateboard deck into a bold and cheeky wall feature.
In addition, the natural wood grain and minimalist hooks give it a modern look, perfect for bathrooms that could use a touch of skate-inspired rebellion.
Step 1: Start with a smooth, sanded skateboard deck. You can seal it with clear polyurethane for water resistance.
Step 2: Position your brackets evenly, one near the top, one near the bottom, leaving enough room for each roll.
Step 3: Drill pilot holes and attach each bracket firmly using screws. You should double-check the spacing to ensure the rolls spin freely.
Step 4: Mount the finished board on the wall using heavy-duty anchors or screws into studs.
If you've got a soft spot for rings and a stash of old skate decks, this creative display stand is the kind of fusion that brings personality to your collection.
Besides, using the curved nose of a skateboard and inserting evenly spaced dowels, this piece doesn’t just hold rings, it presents them like a gallery for your fingers.
Step 1: Mark out a grid pattern on the deck’s upper curve where you want each ring dowel to sit.
Step 2: Drill holes slightly smaller than your dowel width to ensure a snug fit. You should go about ½-1 inch deep.
Step 3: Insert dowels into the holes, then add a dab of wood glue for extra security if needed.
Step 4: Let the glue dry completely before adding your rings. If you’d like, sand any rough edges and add a coat of sealant to keep the display looking polished.
This clever setup transforms a typical loft ladder into a bold design statement, each stair made from a mounted skateboard deck, adding a playful and rebellious twist to a compact living space.
What makes this truly genius is how it blends creativity with function. The solid wood structure supports the boards firmly, while the stairway itself becomes a centerpiece.
Step 1: Cut and position the support beams at an appropriate incline leading to the loft. Use a level to ensure stability.
Step 2: Attach small wood blocks or angled brackets where each deck will sit. These should be evenly spaced and firmly secured.
Step 3: Center each skateboard deck on the supports, nose-to-tail, and screw them into the wood blocks from underneath to prevent splitting.
Repurposed from worn skateboard decks, this mug rack and shelf combo turns a tiled kitchen wall into an effortlessly cool coffee corner.
What gives it soul is the contrast, gritty skate graphics paired with everyday mugs and dishes. Hooks beneath both shelves make this design a space-saver too, perfect for small kitchens that crave personality.
Step 1: Start by cleaning your skateboard decks. Leave any original graphics for character or lightly sand if you plan to repaint or seal.
Step 2: Attach the two vertical decks to the wall using strong wall anchors and brackets.
Step 3: Place one horizontal deck across the bottom section to create the first shelf. Then secure it to the vertical boards with brackets beneath.
Step 4: Repeat with the second shelf at the top, aligning it carefully for balance and stability.
Step 5: Next, screw cup hooks beneath both shelves, spacing them evenly so the mugs hang without touching.
Step 6: Finally, style it with mugs, glasses, spices, or your favorite tea tins. Bonus points for using chipped cups or mismatched sets to match the skater vibe.
Oh my god, you can absolutely turn an old or broken skateboard deck into a vibrant skyline mural that captures the spirit of Los Angeles.
With its jagged top mimicking towering skyscrapers and a road leading into the painted city, this DIY piece feels like a tribute to urban grit and dreamers on the move.
Step 1: Wipe off any dirt or dust from the skateboard using a damp cloth. If the board has old stickers or a glossy finish, lightly sand the surface to help the paint adhere better.
Step 2: Lightly sketch your cityscape design onto the deck with a pencil. You want to include buildings, skyline peaks, trees, and the road, then use the broken edge to your advantage.
Step 3: Start painting the sky and background first using a blend of blues, purples, and black. Let each color dry before layering the next.
Step 4: Use smaller brushes to paint in details like windows, stars, and rooftop outlines. Now, add highlights with white or silver for contrast and nighttime glow.
Step 5: Paint the road on the bottom half with grey tones, adding a center line using white dashes.
Step 6: Once everything is fully dry, spray a layer of clear acrylic sealant over the board to protect your artwork and give it a subtle shine.
Visit our site and see all other available articles!